全自動封膠機常遇到的問題是膠閥問題，下面為大家列出解決膠閥使用時經常發生的問題的有效方法。
The problem that automatic sealing machine often encounters is the problem of rubber valves. The following is an effective way to solve the problem that often occurs in the use of rubber valves.
1. 膠閥滴漏
1. Rubber valve drip leakage
此種情形經常發生予膠閥關畢以后。95%的此種情形是因為使用的針頭口徑太小所致。太小的針頭會影響液體的流動造成背壓, 結果導致膠閥關畢后不久形成滴漏的現象. 過小的針頭也會影響膠閥開始使用時的排氣泡動作.只要更換較大的針頭即可解決這種問題。錐形斜式針頭產生的背壓少, 液體流動順暢。液體內空氣在膠閥關畢后會產生滴漏現象, 好是預先排除液體內空氣,，或改用不容易含氣泡的膠.或先將膠離心脫泡后在使用。
This often happens after the rubber valve is closed. 95% of the cases were due to the small caliber of the needle used. Too small needles can affect the flow of liquid and cause back pressure, resulting in drip leakage shortly after the closure of the rubber valve. Too small needles can also affect the action of exhausting bubbles when the rubber valve starts to use. This problem can be solved by replacing larger needles. Conical oblique needle produces the least back pressure and the smoothest flow of liquid. The air in the liquid will drip after the rubber valve is closed. It is better to exclude the air in the liquid beforehand, or change to a rubber which is not easy to contain bubbles, or to defoam the rubber centrifugally before using it.
2. 出膠大小不一致
2. The size of the glue is not the same.
當出膠不一致時主要為儲存流體的壓力筒或空氣壓力不穩定所產生。進氣壓力調壓表應設定于比廠內低壓力低10至15psi.，壓力筒使用的壓力應介于調壓表中間以上的壓力, 應避免使用壓力介于壓力表之中低壓力部分。膠閥控制壓力應至少60psi以上以確保出膠穩定。后應檢查出膠時間.若小于15/1000秒會造成出膠不穩定.，出膠時間愈長出膠愈穩定。
When the gum is discharged inconsistently, it is mainly caused by unstable pressure cylinder or air pressure for storing fluid. The intake pressure regulator should be set at 10 to 15 psi below the lowest pressure in the factory. The pressure used in the pressure cylinder should be above the middle of the pressure regulator, and the pressure between the middle and low pressure parts of the pressure gauge should be avoided. The control pressure of the rubber valve should be at least 60 psi to ensure the stability of the rubber tapping. Finally, check out the gel time. If less than 15/1000 seconds will cause unstable gel production. The longer the gel production time, the more stable the gel production.

3. 流速太慢
3. Flow velocity is too slow
流速若太慢應將管路從1/4” 改為3/8”。管路若無需要應愈短愈好。除了改管子,還要改出膠口和氣壓,這樣完全加快流速。
If the flow rate is too slow, the pipeline should be changed from 1/4"to 3/8". The shorter the pipeline is, the better. In addition to pipe modification, the rubber outlet and air pressure should also be changed to completely accelerate the flow rate.
4. 流體內的氣泡
4. Bubbles in Fluid
過大的流體壓力若加上過短的開閥時間則有可能將空氣滲入液體內. 解決方法為降低流體壓力并使用錐形斜式針頭。
Excessive fluid pressure and too short valve opening time may infiltrate air into the liquid. The solution is to reduce fluid pressure and use tapered oblique needle.
5. 瞬間膠在膠閥` 接頭` 及管路上堵塞
5. Instantaneous glue blockage in rubber valve `joint'and pipeline
此種情形主要因過多的濕氣或重復使用過的瞬間膠. 應確保使用新鮮的瞬間膠. 將管路以未含濕氣的Aceton丙酮有效清洗過. 使用的空氣應確定完干燥且于廠內空壓與膠閥系統間加裝過濾器. ( 以上方法如仍然無效, 則應使用氮氣. ) 。
This situation is mainly due to excessive moisture or reused instantaneous glue. Fresh instantaneous glue should be ensured. Pipelines should be thoroughly cleaned with non-humid Aceton acetone. The air used should be determined to be dry and filters should be installed between the plant air pressure and the rubber valve system. (If the above methods are still ineffective, nitrogen should be used.) 。
以上的精彩內容由全自動封膠機廠家友情提供，更多的精彩內容請繼續關注我們：http://m.hebeiruizhi.com，我們會有更多的精彩內容為您傾情奉獻！
The above wonderful content is provided by the friendship of the manufacturer of automatic sealing machine. More wonderful content please continue to pay attention to us: http://m.hebeiruizhi.com, we will have more wonderful content to dedicate to you!