當前位置：斷橋鋁門窗設備雙頭鋸調整方法
時間：2023-10-24 來源：http://m.hebeiruizhi.com/ 發布人：昌盛機械
1.斷橋鋁門窗設備雙頭鋸的調整。
1. Adjustment of double head saw for bridge breaking aluminum door and window equipment.
(1)調整壓實缸的位置
(1) Adjusting the position of the compaction cylinder
將鋁合金型材放在鋁門窗設備的工作臺上，將兩個鋸頭的壓缸調整到適合壓制工件的位置，然后將壓缸固定。
Place the aluminum alloy profile on the workbench of the aluminum door and window equipment, adjust the pressure cylinders of the two saw heads to the position suitable for pressing the workpiece, and then fix the pressure cylinders.
(2)調整鋸片進給速度
(2) Adjusting the feed speed of the saw blade
在試驗機器的過程中，如果鋸片進給速度不合適，可以調節工作進給缸的調速接頭，增加或減少進給速度，就可以得到所需的進給速度。
During the process of testing the machine, if the feed speed of the saw blade is not suitable, the speed control joint of the working feed cylinder can be adjusted to increase or decrease the feed speed to obtain the required feed speed.
(3)調整鋸切角度
(3) Adjusting the sawing angle
鋁合金型材精密切割鋸按上述項目進行調整，檢查符合要求后試車30分鐘。
Adjust the precision cutting saw for aluminum alloy profiles according to the above items, and test run it for 30 minutes after checking that it meets the requirements.
(4)以90°角調整設備切割(鋸片垂直于工作臺延伸)。
(4) Adjust the equipment cutting at a 90 ° angle (the saw blade extends perpendicular to the workbench).
鋁合金型材精密切割鋸在出廠前都經過了調試測試，在這里可以直接鋸開一臺鋁合金型材。檢查90度角鋸切面是否符合要求，誤差10'。如果不符合要求，可以調整限位止動器上的螺栓。然后重復鋸切測量以滿足要求。注意把螺母鎖在切割鋸上。
The precision cutting saw for aluminum alloy profiles has undergone debugging and testing before leaving the factory, where you can directly cut open an aluminum alloy profile. Check if the 90 degree angle saw cutting surface meets the requirements with an error of 10&# 39;. If it does not meet the requirements, the bolts on the limit stop can be adjusted. Then repeat the sawing measurement to meet the requirements. Be careful to lock the nut onto the cutting saw.
(5)調整設備切削角度45°(鋸片與工作臺夾角為45°時設置為45°
(5) Adjust the cutting angle of the equipment to 45 ° (set to 45 ° when the angle between the saw blade and the workbench is 45 °
松開工作臺上的鎖緊手柄，擺動角圈要通風，45度角到位后鎖緊手柄。鋸切后檢查型材是否符合要求(誤差10')。如不符合要求，可調整限位器上的限位螺絲，重復鋸切、測量，以滿足要求。然后鎖緊螺絲上的螺母，擰緊鎖緊手柄。
Release the locking handle on the workbench, ventilate the swing angle, and lock the handle when the 45 degree angle is in place. After sawing, check whether the profile meets the requirements (with an error of 10&# 39;). If it does not meet the requirements, the limit screw on the limit device can be adjusted, and the cutting and measurement can be repeated to meet the requirements. Then tighten the nut on the screw and tighten the locking handle.
(6)調整型材切割長度。
(6) Adjust the cutting length of the profile.
角度調整后，還要調整鋁合金型材的切割長度。拉動手柄帶動右鋸頭沿圓形導軌移動到準確位置(見尺指針)，尺指示長度為鋁合金型材短邊長度。切割后，如果切割輪廓長度與要求長度有偏差，應進行微調。微調時，擰緊制動可調手，微調手轉動到所需尺寸。
After adjusting the angle, the cutting length of the aluminum alloy profile should also be adjusted. Pull the handle to move the right saw head along the circular guide rail to the exact position (see ruler pointer), and the length indicated by the ruler is the short edge length of the aluminum alloy profile. After cutting, if there is a deviation between the cutting contour length and the required length, fine adjustments should be made. When fine-tuning, tighten the brake adjustable hand and turn the fine-tuning hand to the required size Firstly, everyone should familiarize themselves with the functions of each button on the panel.
(2)調整好工件的角度和長度后，按下“鋸開始”按鈕。鋸頭電機運轉平穩后，安裝型材，同時按下“夾緊”和“鋸停”按鈕。如遇特殊情況，按下緊急停止按鈕。如果將“鋸頭選擇”開關設置為“左”或“右”位置，則左右鋸頭可獨立工作。如果開關設置為“雙”位，左右鋸頭可同時工作。下班后，關閉主電源。
(2) After adjusting the angle and length of the workpiece, press the "Saw Start" button. After the saw head motor runs smoothly, install the profile and press the "clamp" and "saw stop" buttons at the same time. In case of special circumstances, press the emergency stop button. If the "Saw Head Selection" switch is set to the "Left" or "Right" position, the left and right saw heads can work independently. If the switch is set to the "dual" position, the left and right saw heads can work simultaneously. After work, turn off the main power supply.
有了中空玻璃生產線上面的小總結，希望對廣大客戶有所幫助，如果有什么不理解的或者尋求幫助的請點擊我們的網站：http://m.hebeiruizhi.com或者來電咨詢
With the summary on the production line of multiple insulated glass, we hope it can be helpful to our customers. If you have any questions or need help, please click on our website: http://m.hebeiruizhi.com Or call for consultation
相關新聞 more+
- 中空玻璃生產線的自動化躍遷與產線革命 2026/07/13
- 中空玻璃生產線如何讓兩片玻璃之間“住進”空氣 2026/07/11
- 中空玻璃丁基膠涂布機如何實現“絲滑”涂布？ 2026/07/09
- 雙組份打膠機如何讓密封膠“物盡其用”？ 2026/07/07
- 全自動鋁條折彎機如何為節能門窗打造“鋼筋鐵骨”？ 2026/07/05
- 全自動封膠線破解中空玻璃涂膠均勻性難題 2026/07/03
- 臥式丁基膠涂布機經濟實用實力展現 2026/07/01
- 丁基膠涂布機就是第一道防線的重要作用 2026/06/28
- 雙組份打膠機：精密配比與快捷混合的流體引擎 2026/06/21
- 全自動鋁條折彎機：合理成型與快捷制框的利器 2026/06/19
產品分類Product categories
聯系我們Contact us
- 咨詢熱線：0531-85717458 13705446998
- 公司地址： 山東省德州市齊河安頭鄉企巢工業園
- 掃碼聯系我們：
截屏，微信識別二維碼
微信號：13705446998