如何做好雙組份打膠機在使用中的點膠操作
　　How to do well the dispensing operation of two-component dispenser in use
　　1. 固化元件:對于膠水的固化，一般廠家給出了溫度曲線。一般在室溫下即可固化，在實際應用中應盡量選擇較高的溫度進行固化，使固化后的膠水達到強度和硬度。
　　1. Curing element: for the curing of glue, the general manufacturer gives the temperature curve. Generally, it can be cured at room temperature. In practical application, it should be cured at a higher temperature as far as possible to make the cured glue reach the strength and hardness.
　　2、泡膠機在泡膠的過程中會影響到產品的質量，所以在涂膠前不能有泡膠。
　　2. The quality of the product will be affected by the foam machine in the process of foam, so there should be no foam before coating.
　　3,真空吸入閥建議安裝在配藥機,由于真空回吸功能是防止膠水點膠機不是調劑滴泄漏,如果安裝工具包可以合理調整真空吸入閥,并進一步可以控制滴泄漏和繪畫這兩個病例。
　　3. The vacuum suction valve must be installed in the dispensing machine. Because the vacuum suction function is to prevent the glue dispenser from leakage of dispensing drops, if the installation kit can reasonably adjust the vacuum suction valve, and further control the two cases of drip leakage and painting.
　　標準4、針和類別:針標準會影響在調劑的過程中膠粘劑范圍和精度,當壓力,噴嘴針越大,速度越大,所以要分配的基礎上機器生產產品的侵入性的標準錨點膠針,針直徑長度保持膠點直徑的一半,效果很好。
　　Standard 4, needle and category: needle standard will affect the range and accuracy of adhesive in the process of dispensing. When the pressure and nozzle needle are larger, the speed is larger. Therefore, the invasive standard anchor needle of the product manufactured by the machine on the basis of distribution is required. The diameter length of the needle keeps half of the diameter of the glue point, and the effect is very good.

　　5、點膠量的大小是由點膠機在點膠過程中持續的時間長短決定的，時間越長。
　　5. The size of dispensing volume is determined by the duration of the dispensing machine in the dispensing process, the longer the time.
　　6、在點膠機中一般使用的膠水可能有環氧樹脂、速溶膠、硅膠、厭氧膠、UV膠等。
　　6. The glue commonly used in dispensing machine may be epoxy resin, quick sol, silica gel, anaerobic glue, UV glue, etc.
　　7,侵入性壓力直接影響流的速度膠水,膠水,膠水更糟的活動變得厚,它需要更大的壓力,所以我們應該基于配藥機在生產過程中環境溫度和侵入性膠膠量的特性來調節壓力,膠侵入的壓力是通過其內部壓力調節閥進行調理。
　　7. The invasive pressure directly affects the speed of flow. The worse activities of glue and glue become thicker. It needs more pressure. Therefore, we should adjust the pressure based on the characteristics of the ambient temperature and the amount of invasive glue in the production process of the dispensing machine. The pressure of glue invasion is regulated by its internal pressure regulating valve.
　　以上雙組份打膠機的介紹希望對您有所幫助，我們的產品質量好，價格合理，真誠歡迎您選購，我們竭誠為您服務。
　　The introduction of the above two-component dispenser is hoped to be helpful to you. Our products are of good quality and reasonable price. We sincerely welcome you to buy and we will serve you wholeheartedly.