當前位置：雙組份打膠機在使用中要注意什么？
時間：2023-09-07 來源：http://m.hebeiruizhi.com/ 發布人：昌盛機械
高效氣動雙組份打膠機是集技術生產的中空玻璃密封膠打膠機，A組分泵和B組分泵膠分別采用氣動系統驅動，采用無觸點電器控制系統控制，換向靈敏可靠，其獨特的方便可調試配比機構，大限度地保證雙組份膠近乎苛刻的配比要求，出膠連續均勻，涂膠效果好，生產效率高。
The high-efficiency pneumatic dual component sealant applicator is a hollow glass sealant applicator that integrates domestic and foreign technologies. The A component pump and B component pump are respectively driven by pneumatic systems and controlled by contactless electrical control systems, with sensitive and reliable commutation. Its unique and convenient and adjustable proportioning mechanism ensures that the dual component sealant meets almost strict proportioning requirements to the maximum extent, with continuous and even glue output, good gluing effect, and high production efficiency.
1.由于雙組份密封膠的固化需要一定時間，因此雙組份打膠機，已涂了雙組份密封膠的玻璃應水平輕輕搬動。
Due to the time required for the curing of the two-component sealant, the glass coated with the two-component sealant should be gently moved horizontally in the two-component sealant applicator.
2.A組、B組份膠應保持清潔，嚴防異物進入膠中。
2. Components A and B of the adhesive should be kept clean to prevent foreign objects from entering the adhesive.
3.在連續工作過程中，膠槍每次停止工作時間一般不得超過20分鐘，否則，應用A組份膠沖出全部混合膠，直至單一的A組份膠從槍口排出為止。
During continuous operation, the stopping time of the glue gun should generally not exceed 20 minutes. Otherwise, all mixed glue should be washed out using component A glue until a single component A glue is discharged from the gun mouth.
4.高壓膠管不得強行擠壓、彎曲，防止影響系統正常工作。
4. The high-pressure hose should not be forcibly squeezed or bent to prevent affecting the normal operation of the system.
5.混膠器應經常保持暢通，以保證良好的出膠效果。如遇堵塞情況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. The mixer should always be kept unobstructed to ensure a good adhesive release effect. In case of blockage, it can be soaked in acetone and cleaned. It is recommended to clean every 5 groups.
6.當膠槍長時間不用時（超過一周），應拆下槍體使用溶劑將膠槍和混膠器內的殘留膠體清洗干凈。
When the glue gun is not used for a long time (more than a week), the gun body should be removed and solvent should be used to clean the residual glue in the glue gun and mixer.
7.不同雙組份膠生產廠家所生產的膠內含雜質數量不同，根據實際情況清晰B組分的過濾網及單向止回閥，建議每兩組清洗一次
7. The amount of impurities in the adhesive produced by different manufacturers of two-component adhesive varies. Based on the actual situation, it is recommended to clean the filter screen and one-way check valve of component B every two groups
本文由雙組份打膠機提供技術支持，更多的詳細精彩內容請點擊我們的網站http://m.hebeiruizhi.com ，我們將會全心全意為您提供滿意的服務。
This article is supported by a dual component adhesive machine. For more detailed and exciting content, please click on our website http://m.hebeiruizhi.com We will wholeheartedly provide you with satisfactory service.
上一篇：中空玻璃設備的日常維護保養事項
下一篇：丁基膠涂布機使用中如何進行檢測？
相關新聞 more+
- 中空玻璃打膠機，助您開啟高效生產新時代！ 2026/02/19
- 中空玻璃生產線打膠機傳送V帶不平衡？這樣調，傳送平穩不跑偏 2026/02/13
- 中空玻璃生產線打膠難題：壓力夠卻打不滿膠？這樣排查就解決 2026/02/12
- 全自動封膠線實操科普：山東昌盛板壓段，筑牢封膠質量核心防線 2026/02/10
- 中空玻璃生產線實操科普：小玻璃清洗機反轉打滾？這樣解決最省心 2026/02/06
- 全自動封膠線實操科普：白膠泵密封圈這樣換，杜絕漏膠保順暢 2026/02/04
- 雙組份打膠機實操科普：出膠體這樣保養維護，延長壽命保順暢 2026/02/02
- 中空玻璃生產線：清洗機這樣保養，清潔高效更耐用 2026/01/30
- 全自動封膠線實操科普：板壓壓合效果差？四角落差這樣調精準 2026/01/28
- 雙組份打膠機實操科普：黑膠泵過濾這樣清洗，避免堵塞保順暢 2026/01/27
產品分類Product categories
聯系我們Contact us
