很多人在買完設備之后，就認為說明書沒用了。隨手一扔，不知所蹤。考慮到很多人都可能會這樣，今天全自動封膠機小編就特地給大家總結下中空玻璃全自動封膠機的小問題以及解決辦法，有需要的小伙伴們可以收藏起來呦。
Many people think the instructions are useless after they have bought the equipment. Just throw it away and you don't know where it is. Considering that many people may be like this, today's small edition of automatic sealant machine specially summarizes the small problems and solutions of hollow glass automatic sealant machine, and small partners in need can collect it.
中空玻璃自動打膠機自身帶著自我保護功能，主要針對于停電自我保護。這就意味著，如果在工作過程中，突然停電的話，它會自動關機。即使在來電，它也不會在自動啟動。這時候就需要我們自己將旋鈕撥回停位，在撥回開位就可以啟動了。這個可以注意一下。
Hollow glass automatic gluing machine itself has self-protection function, mainly aimed at power failure self-protection. This means that if there is a sudden power failure during the working process, it will shut down automatically. Even when a call comes, it doesn't start automatically. At this time, we need to dial the knob back to the parking position, in the dial back to the open position can start. You can pay attention to this.
在結束工作時，一定要把活塞離開丁基膠，要將膠缸置于退的位置，在大約2至3秒后置于停。這很重要，在未加熱或未升溫至設定溫度時，膠缸狀態開關建議置于“停”，否則會出現機械故障
At the end of the work, the piston must be removed from the butyl rubber, and the cylinder should be placed in the retreat position and stopped after about 2 to 3 seconds. It is very important that the cylinder state switch must be put on "stop" when it is not heated or heated to the set temperature, otherwise mechanical failure will occur.
一般中空玻璃打膠機膠缸溫度設定在110～120℃，膠頭溫度設定在120～140℃，就能正常工作，但，由于各丁基膠生產廠家配料比例、價格工藝不同，生產出的丁基膠的熱熔溫度也不同，所以，在使用不同廠家的丁基膠時，先手動試打膠，打出的膠太稀，降低設定溫度，若不出膠或不粘;則升高設定溫度。
Generally, the cylinder temperature of hollow glass glue beater is set at 110-120 C, and the head temperature is set at 120-140 C, which can work normally. However, due to the different proportions and price processes of butyl rubber manufacturers, the hot melting temperature of butyl rubber produced is also different. Therefore, when using butyl rubber from different manufacturers, the glue produced is too thin and the setting temperature is lowered. If no glue or no glue is produced, the setting temperature will be raised.

調試的注意事項：
Notes for debugging:
1、在當天機器操作完畢后要把膠管內的膠沖出，防止硬化；如果長時間不實用要注意用煤油清洗膠管和膠槍。
1. After the machine is finished, the glue in the rubber tube should be washed out to prevent hardening. If it is not practical for a long time, we should pay attention to cleaning the rubber tube and gun with kerosene.
2、雙組份打膠機使用的硅酮膠或聚硫膠要注意雜質不能過高，低質量的膠容易堵塞膠管的過濾系統，造成出膠不暢或不均勻。
2. Silicone glue or polysulfide glue used in two-component glue beater should pay attention to the impurities should not be too high, low-quality glue is easy to block the filter system of rubber hose, resulting in poor or uneven glue production.
3、在更換膠的品種時要非常注意把雙組份打膠機內殘留的膠沖凈，好清洗，因?yàn)椴煌贩N甚至的膠容易反應堵塞機器。
3. When changing the type of glue, special attention should be paid to rinsing the residual glue in the two-component glue beater, and it is better to clean it, because the glue of different varieties or even brands can easily react to clogging the machine.
4、液壓站系統的壓力，不能調的太高，要根據室內環境溫度等實際情況，調至滿足膠嘴正常出膠均勻打膠即可。打開液壓站時一定要打開膠槍，否則B組份管路壓力將升得很高，造成安全事故。
4. The pressure of hydraulic station system can not be adjusted too high. According to the actual situation of indoor environment temperature, it can be adjusted to meet the normal tapping of rubber nozzles. When opening the hydraulic station, the rubber gun must be opened, otherwise the pressure of component B pipeline will rise very high, resulting in safety accidents.
本章由全自動封膠機給大家介紹的內容就暫且到這里，希望我們的解答能夠幫助到您，如果您對此還有疑問，詳情請咨詢我們的官方。http://m.hebeiruizhi.com
The content of this chapter introduced by automatic sealing machine is here for the time being. I hope our answers can help you. If you have any questions about this, please consult our official for details. http://m.hebeiruizhi.com