雙組份打膠機的構造原理
The Construction Principle of Two-Component Gluing Machine
1.由于雙組份密封膠的固化需求一定工夫，因而，已涂了雙組份密封膠的玻璃應程度悄悄搬動。
1. Because of the curing requirement of the two-component sealant, the glass coated with the two-component sealant should be moved quietly.
2.A組、B組份膠應堅持清潔，嚴防異物進入膠中。
2. Group A and B glue should be kept clean and foreign bodies should be strictly prevented from entering the glue.
3.在延續任務進程中，膠槍每次中止任務工夫普通不得超越20分鐘，否則，使用A組份膠沖出全部混合膠，直至單一的A組份膠從槍口排出爲止。
3. In the process of continuing the task, the time for each suspension of the rubber gun should not exceed 20 minutes. Otherwise, use the A-component glue to punch out the whole mixture until a single A-component glue is discharged from the muzzle of the gun.

4.高壓膠管不得強行擠壓、彎曲，避免影響零碎正常任務。
4. High-pressure rubber hose shall not be forced to extrude or bend, so as to avoid affecting fragmentary normal tasks.
5.混膠器應常常堅持疏通，以保證良好的出膠效果。如遇梗塞狀況，可用丙酮浸泡后清洗。建議每5組清洗一次。
5. Mixers should always be dredged in order to ensure a good gumming effect. In case of infarction, it can be washed after soaking in acetone. It is recommended to clean every 5 groups.
6.當膠槍長工夫不必時（超越一周），應拆下槍體運用溶劑將膠槍和混膠器內的殘留膠體清洗潔凈。
6. When the glue gun is unnecessary for a long time (more than a week), the gun body should be removed and the residual colloid in the glue gun and mixer should be cleaned by solvent.
7.不同雙組份膠消費廠家所消費的膠內含雜質數量不同，依據實踐狀況明晰B組分的過濾網及單向止回閥，建議每?jī)山M清洗一次。
7. The amount of impurities in the rubber consumed by different two-component rubber manufacturers is different. According to the practice, it is recommended that the filter screen and check valve of component B be cleaned once for each two groups.
8.明顯因膠體固化所形成的膠槍、管路或零件的毛病，一概不在保修范圍之內。
8. Any defects of rubber guns, pipes or parts formed by gel solidification are not covered by warranty.
9.活期給各泵的加油口加油，應保證油霧器內不時油。
9. To refuel the refuelling ports of pumps on demand, it is necessary to ensure that the oil mist is refuelled from time to time.
本文由濟南昌盛機械http://m.hebeiruizhi.com提供整理,想了解更多雙組份打膠機知識，歡迎關注我們，謝謝!!
This article is provided by Jinan Changsheng Machinery http://m.hebeiruizhi.com. Want to know more about two-component glue machine. Welcome to pay attention to us, thank you!!