春節停機別忘保養！中空玻璃加工設備這樣維護，開春開機不趴窩

　　Don't forget maintenance during the Spring Festival shutdown! The insulated glass processing equipment is maintained in this way, and it won't collapse when it starts up in spring

　　春節假期往往長達半月甚至更久，不少玻璃廠會直接關停中空玻璃加工設備。但若放任設備閑置不加維護，殘留的水汽、膠漬、雜質很容易引發故障——噴頭堵塞、部件卡滯、膠水泄漏等問題頻發，開春開機后不僅要耗費大量時間檢修，還可能耽誤訂單生產。作為專注中空玻璃設備的廠家，結合設備特性整理了針對性維護方案，按類別操作就能讓設備保持良好狀態，來年開工順暢無憂。

　　The Spring Festival holiday often lasts for half a month or even longer, and many glass factories will directly shut down their insulated glass processing equipment. But if the equipment is left idle without maintenance, residual water vapor, glue stains, and impurities can easily cause malfunctions - problems such as nozzle blockage, component jamming, and glue leakage occur frequently. After starting up in spring, it not only takes a lot of time for maintenance, but may also delay order production. As a manufacturer specializing in insulated glass equipment, we have compiled targeted maintenance plans based on the characteristics of the equipment. By operating according to categories, we can keep the equipment in good condition and ensure smooth and worry free operation in the coming year.

　　中空玻璃清洗機的維護核心是防范水垢堆積與部件堵塞。清洗機的水箱、管道長期殘留水分和清洗劑，停機后極易滋生水垢、沉積玻璃碎屑，進而堵塞噴淋噴嘴，導致開春清洗玻璃時出現水印、清洗不凈等問題。維護時需先將水箱內的積水徹底排空，包括管道內的殘留水分，避免死角留存；隨后用清水反復沖洗水箱和管道1-2次，清除殘留的清洗劑與雜質，再將內壁擦干；關鍵步驟是拆卸噴淋噴嘴，用軟毛刷仔細清理噴孔內的污垢，確保通暢后重新安裝，這一步雖繁瑣，卻能有效避免開機后噴嘴堵塞；最后在傳送帶軸承等金屬部件表面涂抹防銹油，防止潮濕環境下生銹。

　　The maintenance core of the hollow glass cleaning machine is to prevent scale accumulation and component blockage. The water tank and pipeline of the cleaning machine have long-term residual moisture and cleaning agents, which can easily breed scale and deposit glass debris after shutdown, thereby blocking the spray nozzle and causing problems such as water marks and incomplete cleaning when cleaning glass in spring. During maintenance, it is necessary to thoroughly drain the accumulated water in the water tank, including any residual moisture in the pipes, to avoid dead corners from remaining; Subsequently, rinse the water tank and pipes repeatedly with clean water 1-2 times to remove residual cleaning agents and impurities, and then dry the inner walls; The key step is to disassemble the spray nozzle, carefully clean the dirt inside the spray hole with a soft bristled brush, ensure unobstructed flow, and reinstall. Although this step is cumbersome, it can effectively avoid nozzle blockage after turning on the machine; Finally, apply rust proof oil on the surface of metal components such as conveyor bearings to prevent rusting in humid environments.

　　合片機、合片充氣板壓機的維護重點在于保護定位系統與密封部件。這類設備依賴精準定位和密封性能保障生產質量，長期閑置可能導致定位傳感器受潮失靈、密封膠條老化，進而引發合片偏移、充氣泄漏等問題。維護時應先清理工作臺面的玻璃渣與膠漬，尤其要注意擦拭紅外或激光定位傳感器，需使用干布輕擦，避免濕布導致受潮失靈；仔細檢查鋁條卡槽與密封膠條，若發現老化、磨損痕跡，應趁停機期間及時更換，避免開春生產時延誤工期；同時排空氣缸、氣管等氣動元件內的壓縮空氣，防止低溫環境下凍裂，在金屬活動部位添加潤滑脂，確保開機后運轉靈活。

　　The maintenance focus of the laminating machine and laminating inflatable plate press is to protect the positioning system and sealing components. This type of equipment relies on precise positioning and sealing performance to ensure production quality. Long term idle may cause the positioning sensor to become damp and malfunction, the sealing strip to age, and subsequently lead to problems such as misalignment and inflation leakage. When maintaining, the glass shards and glue stains on the workbench should be cleaned first, especially paying attention to wiping the infrared or laser positioning sensors. A dry cloth should be used to gently wipe them to avoid moisture and malfunction caused by wet cloth; Carefully inspect the aluminum strip slot and sealing strip. If aging or wear marks are found, they should be replaced in a timely manner during the shutdown period to avoid delaying the construction period during spring production; At the same time, empty the compressed air inside the pneumatic components such as cylinders and air pipes to prevent freezing and cracking in low-temperature environments. Add lubricating grease to the metal moving parts to ensure flexible operation after startup.

　　打膠機、丁基膠涂布機的維護關鍵是清理膠路殘留，防止膠水凝固。膠管、膠泵內殘留的丁基膠或密封膠長期閑置會凝固結塊，堵塞管路，后續清理難度極大。維護時需先將膠桶內剩余的膠水用完或密封保存，避免浪費；然后使用設備專用清洗液或溶劑，反復沖洗膠管、膠泵與膠頭3-4次，直至排出的液體無膠渣殘留；最后在膠泵內壁與膠頭密封處涂抹專用潤滑油，既防止部件干磨損壞，也能避免殘留膠水凝固粘連。

　　The key to maintaining glue dispensing machines and butyl rubber coating machines is to clean the residue on the glue path and prevent the glue from solidifying. The residual butyl rubber or sealant in the rubber hose and pump will solidify and block the pipeline if left idle for a long time, making it extremely difficult to clean afterwards. During maintenance, the remaining glue in the glue bucket should be used up or sealed for storage to avoid waste; Then use equipment specific cleaning solution or solvent to repeatedly rinse the rubber hose, rubber pump, and rubber head 3-4 times until there is no residue of rubber residue in the discharged liquid; Finally, apply special lubricating oil to the sealing area between the inner wall of the glue pump and the glue head, which not only prevents dry wear and damage to the components, but also avoids residual glue from solidifying and sticking.

　　所有中空玻璃加工設備均需做好斷電、防潮、防塵的通用維護。首先關閉總電源并拔掉插頭，避免春節期間電壓波動損壞電路；若車間環境潮濕，可在設備旁放置干燥劑，尤其要重點保護觸屏、電路板等精密控制系統，防范受潮短路；最后用防塵布將設備整體覆蓋，阻擋灰塵進入部件縫隙，減少后續清潔工作量。

　　All insulated glass processing equipment must undergo general maintenance for power-off, moisture resistance, and dust prevention. Firstly, turn off the main power and unplug the plug to avoid voltage fluctuations that may damage the circuit during the Spring Festival; If the workshop environment is humid, desiccants can be placed next to the equipment, especially to protect precision control systems such as touch screens and circuit boards from moisture and short circuits; Finally, cover the entire device with a dust-proof cloth to prevent dust from entering the gaps of the components and reduce the subsequent cleaning workload.

　　春節設備保養看似占用時間，實則能有效規避開春后的檢修麻煩與生產延誤。按上述方法分類維護，既能延長設備使用壽命，也能保障開工后快速恢復高效生產。若對具體部件的維護操作存在疑問，可隨時咨詢設備廠家獲取專業指導，讓設備在假期后依然保持最佳狀態，助力新一年訂單順利推進。

　　Spring Festival equipment maintenance may seem time-consuming, but it can effectively avoid maintenance troubles and production delays after the start of spring. Classifying and maintaining according to the above methods can not only extend the service life of equipment, but also ensure the rapid recovery of efficient production after starting work. If you have any questions about the maintenance operation of specific components, you can consult the equipment manufacturer at any time for professional guidance, so that the equipment can maintain its best condition after the holiday and help smoothly advance orders for the new year.

　　本文由  中空玻璃加工設備 友情奉獻.更多有關的知識請點擊  http://m.hebeiruizhi.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from insulating glass processing equipment For more related knowledge, please click http://m.hebeiruizhi.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.