一、雙組份打膠機的操作說明

　　I. operation instructions of two component gluing machine

　　1.接通電源(380V 三相四線)和氣源(0.6-0.7MPa)。

　　1. turn on the power supply (380V three-phase four wire) and air source (0.6-0.7MPa).

　　2.打開A,B膠供膠閥門，關閉B膠回流閥門。

　　2. open A, B glue valve, turn off B glue return valve.

　　3.在控制面板上選擇“開機”然后檢查一下A,B膠是否工作正常。此時供膠機混膠工作準備就緒，如果長時間不用(超過15分鐘)或者是下班時要在控制面板上選擇“沖槍”，然后打開B膠回流閥門，關閉B膠供膠閥門.此時供膠機沖槍準備工作就緒。 調整機器的水平度，調節地腳的高度使機身水平。接通電源后先檢查各電機的旋轉方向是否正確，接通與CL—A—01打膠機的膠管、信號。

　　3. select "boot" on the control panel, and then check "A" and see if the B glue is working properly. This glue mixing machine is ready, if not a long time (more than 15 minutes) or work to select the "red gun" in the control panel, and then open the B glue return valve closed B glue glue valve. This glue machine gun is ready at. Adjust the level of the machine, adjust the height of the foot, so that the fuselage level. After connecting the power supply, check the direction of rotation of the motor is correct, switch on and CL - A - 01 rubber machine hose, signal.

　　二、雙組份打膠機結構

　　Two 、 structure of two component gluing machine

　　1、CL-B-01型雙組份供膠機主要有A組份提膠泵、B組份提膠泵， A、B膠增壓裝置，高壓柱塞泵，A、B膠泵連接裝置，雙組分比例調節機構，高壓出口安全分流裝置，液壓控制系統，氣動控制系統及電器控制系統等組成。

　　1, CL-B-01 type two-component glue machine main component A, B component of gel extraction pump rubber pump, A, B glue pressurizing device, high pressure piston pump, A pump, B glue connecting device, double component ratio adjusting mechanism, a high pressure outlet safety shunt device, hydraulic control system, gas composition pneumatic control system and electric control system etc..

　　2、A組份提膠由電動齒輪泵提供，經管道輸送至油壓驅動的A膠高壓柱塞泵增壓。B組份提膠由氣動往復泵提供，經管道輸送至油壓驅動的B組分高壓柱塞泵增壓。

　　2, A group of rubber extraction by the electric gear pump, pipeline delivery to the hydraulic pressure driven A glue high pressure plunger pump pressurization. B component extraction is provided by pneumatic reciprocating pump and conveyed by pipeline to B component driven by oil pressure.

　　A、B膠的體積比例由雙組分比例調節機構調整，然后，同時送入打膠機混合器，混合器由36節以上混合裝置組成，雙組份膠充分混合后到達涂膠槍，從膠嘴噴出，涂布于中空玻璃的邊緣進行封邊。膠嘴設有啟動快速關閉閥，用以準確控制出膠時間。

　　The volume ratio of A, B glue by the two-component proportion regulating mechanism, and at the same time, into the glue mixer, the mixer is composed of 36 sections above the mixing device, two-component adhesive after mixing to glue gun, glue from the spout, the edge is coated on the insulating glass edge. The rubber nozzle is equipped with a quick start shut-off valve to accurately control the gum release time.

　　3、A、B組份體積比例調節由雙組分比例調節機構完成。 A、B組份比例分配比的調節主要靠調節高壓泵前端連軒上的滑塊，向上調B膠出膠少，向下調B膠出膠多。滑塊中心距上端軸中心線16.4cm時，A/B膠的比例為10比1。

　　3, A, B component volume ratio adjustment by a two component proportional adjustment mechanism to complete. The proportion of A and B components is adjusted mainly by adjusting the front of the high-pressure pump, and even on the slider on the porch, up to the B gel, less gum, down B glue, more gum. The ratio of A/B glue is 10 to 1 when the center line of the block is 16.4cm.

　　以上便是雙組份打膠機今天的分享，您還滿意嗎，歡迎關注我們的網站:http://m.hebeiruizhi.com/并且關注我們的產品，我們將為您提供優良的產品，衷心的愿與您建立合作關系。

　　The above is to share the two-component glue machine today, you still satisfied with it, welcome to our website: http://m.hebeiruizhi.com/ and pay attention to our products, we will provide you with excellent products, sincerely wish to establish business relationship with you.